Durock® Setting Type Basecoat

USG ME Portland cement and dry latex polymers make up the Durock® Basecoat, which is made specifically for external walls, ceilings, and the DUROSCREENTM 2100System (EIFS, Exterior insulation and finishing system). The reinforcement is done with exterior tape of the Durock® brand on-site at board joints and inside and outside corners. meets or surpasses the following specifications: EN 99E-1, ASTM C472-79, C266-86, and C109.

 

For joints treatment in Durock® system, neat finished edges, is used for embedding, as a coating over the entire surface and joints treatment between boards of Durock® brand cement board and edges that not required vinyl bead. For embedding fiberglass mesh and as a bonding for insulating sheathing density Stone Wool panels in EIFS (EIFS, Exterior insulation and finishing system) INSULCREEN ™ 2100, for bonding Stone Wool panels on Durock® system and masonry systems

 

As a coating of 2.5mm over the entire surface and joints treatment between boards of Durock® brand cement board, approximate Coverage - 7 to 8 square meter per bag. As a coating of 1.5mm over the entire surface and joints treatment between boards of Durock® brand cement board, approximate Coverage - 9 to 10 square meter per bag. As a bonding for insulating sheathing rigid extruded polystyrene or Stone Wool panel approximate Coverage - 12 to 14 square meters per bag.

SAR 1.00
In stock
SKU
PBCD-25
  • EIFS

  • Wet Area

Overview

USG ME Portland cement and dry latex polymers make up the Durock® Basecoat, which is made specifically for external walls, ceilings, and the DUROSCREENTM 2100System (EIFS, Exterior insulation and finishing system). The reinforcement is done with exterior tape of the Durock® brand on-site at board joints and inside and outside corners. meets or surpasses the following specifications: EN 99E-1, ASTM C472-79, C266-86, and C109.

 

For joints treatment in Durock® system, neat finished edges, is used for embedding, as a coating over the entire surface and joints treatment between boards of Durock® brand cement board and edges that not required vinyl bead. For embedding fiberglass mesh and as a bonding for insulating sheathing density Stone Wool panels in EIFS (EIFS, Exterior insulation and finishing system) INSULCREEN ™ 2100, for bonding Stone Wool panels on Durock® system and masonry systems

 

As a coating of 2.5mm over the entire surface and joints treatment between boards of Durock® brand cement board, approximate Coverage - 7 to 8 square meter per bag. As a coating of 1.5mm over the entire surface and joints treatment between boards of Durock® brand cement board, approximate Coverage - 9 to 10 square meter per bag. As a bonding for insulating sheathing rigid extruded polystyrene or Stone Wool panel approximate Coverage - 12 to 14 square meters per bag.

  • EIFS

  • Wet Area

Specifications

 

Durock® Setting Type Basecoat features

  • For interior and exterior Durock® boards and cement boards applications.
  • Specially formulated for Durock® system.
  • High flexibility.
  • Exceptional bond to the substrate.
  • High performance designed for use in EIFS system.
  • Asbestos-free product.

 

Durock® Setting Type Basecoat application

Place 5 liters of water in a container. Start the mixer; slowly add Basecoat and mix until to obtain a homogeneous mixture. Add more water if is necessary. Approximate water-cement ratios for Basecoat (hand or machine application) are 6 liters per bag. Mix plaster with a cage-type paddle driven by a heavy-duty drill capable of producing 300 to 450 rpm.

 

When the mixture is smooth and free of lumps, let stand 15 minutes, and then re-mix to a smooth paste. The surface where you will apply the cement must be completely clean, dry and free of dust, ice, grease, oil or other substances that may prevent adhesion.

 

Fill joints with Durock®® Basecoat with a Hammer-End Joint Knife and then place the reinforcing exterior tape DUROCK® brand, retroweling removing excess of Basecoat in order to embed the tape. Cover corners and vinyl beads. The thickness of the Durock® Basecoat must be thin, no more than 1 mm. Remove excess with a flat metal wool or polystyrene wet. Allow dry at least 4 hours.

 

Once the joints are dry, apply a uniform layer of 2 mm thick over the entire surface of Basecoat Durock® brand with a flat trowel. Allow dry at least 24 hours before applying any seal or finish

Documents Files
Ceiling Specification Format (CSI)
Warranty
Sustainability tool
Installations

Innovative Interior Finishes

SHEETROCK®️ Ready Mixed Joint Compounds

Jointing and finishing mixing of compounds

Jointing and finishing joint tapes

Jointing and finishing recess and tapered edge joint

Jointing and finishing butt and square edge joints

Jointing and finishing internal corners

Jointing and finishing external corners

Compound additions jointing and finishing mechanical jointing tools

Jointing and finishing screws and fasteners

Jointing & Finishing of Plasterboard System

Sales Offices

Your nearest sales office in Turkey

USG Middle East - Turkey

P.O.BOX: Turkey Turkey - Simirna Endüstriyel Kimya San. ve Dış Tic. A.Ş. A.O.S.B, 10040. Sk. No:9, 35620 Atatürk Osb/Çiğli/İzmir

Your directions:

Change to walking, cycling, public transport or driving.